Cioks

Cioks Split Flex Adaptor Cable. Splits the power from one output to two connectors.
Length: 30/50cm. Plug type: 5,5/2,1mm.

Cioks Flex Adaptor Cable.
Length: 50cm. Plug type: 2-pin DIN plug.

Cioks Flex Adaptor Cable.
Length: 30cm. Plug type: 9V Battery clip connector.

Cioks Flex Adaptor Cable.
Length: 50cm. Plug type: 3,5mm mini plug angled. Tip Positive.

Cioks Flex Adaptor Cable.
Length: 50cm. Plug type: 5,5/2,5mm angled plug. Tip Positive.

This Flex is doubling the voltage, 50cm with 5.5/2.5mm centre positive DC-plug (green)

Cioks Flex Adaptor Cable.
Length: 50cm. Plug type: 5,5/2,1mm angled plug. Tip Positive.

This Flex cable makes it possible to power three pedals using one outlet of the power supply. You need to make sure that the three pedals can all be powered by the same voltage and that they all use the most common 5.5/2.1mm centre negative DC-plug (BOSS standard). The good thing about this daisy chain cable is that you have more length in between the DC-plugs (30cm) which gives more design freedom when placing the effects on your pedal board. The first plug on the cable is 50cm from the power supply.

Cioks Flex Adaptor Cable.
Length: 50cm. Plug type: 5,5/2,1mm straight plug. Tip Negative.

Cioks Flex Adaptor Cable.
Length: 30cm. Plug type: 5,5/2,1mm angled plug. Tip Negative.

This split adapter Flex makes it possible to power two pedals using only one outlet of the power supply. You

AC10 is a member of CIOKS professional range of dedicated multi-output power supplies for effect pedals. Its two powerful AC sections with 800mA each offer voltages 9, 12 and 16V AC. If you have one or two pedals in your setup, which requires an AC power source, AC10 is the right choice. It powers all vacuum tube pedals from Electro-Harmonix, Kingsley, older Blackstar HT series, the Whammy or JamMan from DigiTech, Tube Rotosphere, Tubeman, Tube Factor or Replex from Hughes & Kettner or EBS Valve Drive just to mention a few. If you only have one AC pedal, you can convert one of the AC sections into a powerful DC section offering 600mA with voltages 9, 12 and 15V DC. The first 4 isolated outlets offering a total of 600mA are ideal for pedals using 9 or 12V DC at lower currents op to 200mA.

Loads of power, almost endless compositions of different voltages and a great selection of included Flex cables make this power supply a really strong tool for powering big pedal boards with many different pedals. CIOKS CIOKOLATE power supply will power several high current digital pedals, high voltage 18, 24 or even 40V pedals, one or two AC pedals, one or two Radial Tonebone pedals or simulating a dying battery it will power your old favourite fuzz or overdrive. On top of that it will of course also power all your standard 9V pedals from its many isolated outlets.

Fuse for CIOKOLATE PSU, 5x20mm, slow blow T, 1.000mA. You might blow the fuse of your CIOKS power supply. Normally it only happens if the power supply's mains voltage selector switch is set to 115V and you connect it to 230 or 240V mains. In this case you'll need to replace the fuse. Please look at the bottom of your unit which type is the right one.

Fuse for DC10, AC10, TC10 or Pussy Power PSU, 5x20mm, slow blow T, 500mA. You might blow the fuse of your CIOKS power supply. Normally it only happens if the power supply's mains voltage selector switch is set to 115V and you connect it to 230 or 240V mains. In this case you'll need to replace the fuse. Please look at the bottom of your unit which type is the right one.

This adapter allows you to link two power supplies, where two or more power supplies are powered with a single mains power cord. You can use this adapter and feature with all three power supplies from the link range and also the new Power Factor 2.

Packed in a zip-bag this kit contains all the additional parts needed to mount a CIOKS 10 power supply underneath a Pedaltrain pedal board (PT-Jr, PT-1, PT-2, PT-3 or T-PRO).